AMB26 (RTL8720DF) Supported ARDUINO built-in example table
There are many built-in examples in Arduino. In the table below, we list all examples that are compatible with Ameba.
Please refer the following link to set up Ameba for Arduino IDE.
Refer the following link for Arduino built-in example details.
Please refer the following link to set up Ameba for Arduino IDE.
Refer the following link for Arduino built-in example details.
| Category | Name | Comment | Remarks |
| 01. Basics | AnalogReadSerial | Connect potentiometer to 3.3V. ADC pin used, up to 3.3V and can be calibrated by using analogSet(float gain, float offset). | ADC pin options A4 (PB1), A5 (PB2), A6 (PB3). ADC pin reading voltage range 0 to 3.3V. ADC value can be calibrated by modifying _offset and _gain using 2 points calibration method. analogSet(float gain, float offset) can be used to update the calibrated offset and gain values. |
| BareMinimum | |||
| Blink | LED_BUILTIN sets to any GPIO pins. | ||
| DigitalReadSerial | |||
| Fade | For “analogWrite()”, use PWM capable pin. | PWM capable Pin 2, 3, 5, 6, 7, 14, 15, 16, 17, 18, and 19. | |
| ReadAnalogVoltage | ADC pin used, up to 3.3V and can be calibrated by using analogSet(float gain, float offset). | ||
| 02. Digital | BlinkWithoutDelay | LED_BUILTIN sets to any GPIO pins. | |
| Button | |||
| Debounce | |||
| DigitalInputPullup | |||
| StateChangeDetection | |||
| toneKeyboard | ADC pin used, up to 3.3V and can be calibrated by using analogSet(float gain, float offset). For “analogRead()”, use ADC pin name (A4 to A6) instead the integer number. For “tone()” and “noTone()”, use PWM capable pin. | ||
| toneMelody | |||
| toneMultiple | |||
| tonePitchFollower | |||
| 03. Analog | AnalogInOutSerial | ADC pin used, up to 3.3V and can be calibrated by using analogSet(float gain, float offset). For “analogWrite()”, use PWM capable pin. | |
| AnalogInput | |||
| AnalogWriteMega | |||
| Calibration | |||
| Fading | |||
| Smoothing | |||
| 04. Communication | ASCIITable | ||
| Dimmer | For “analogWrite()”, use PWM capable pin. | ||
| Graph | Connect potentiometer to 3.3V. ADC pin used, up to 3.3V and can be calibrated by using analogSet(float gain, float offset). | ||
| Midi | Use Serial1, MIDI jack pin 5 connected to SERIAL1_TX; Use Serial2, MIDI jack pin 5 connected to SERIAL2_TX. | ||
| MultiSerial | |||
| PhysicalPixel | |||
| SerialCallResponse | ADC pin used, up to 3.3V and can be calibrated by using analogSet(float gain, float offset). For “analogRead()”, use ADC pin name (A4 to A6) instead the integer number. | ||
| ReadASCIIString | For “analogWrite()”, use PWM capable pin. | ||
| SerialEvent | |||
| SerialPassthrough | Serial options, Serial, Serial1 or Serial2. | ||
| VirtualColorMixer | ADC pin used, up to 3.3V and can be calibrated by using analogSet(float gain, float offset). | ||
| 05. Control | Arrays | ADC pin used, up to 3.3V and can be calibrated by using analogSet(float gain, float offset). For “analogWrite()”, use PWM capable pin. | |
| ForLoopIteration | |||
| IfStatementConditional | |||
| switchCase | |||
| switchCase2 | |||
| WhileStatementConditional | |||
| 06. Display | barGraph | ADC pin used, up to 3.3V and can be calibrated by using analogSet(float gain, float offset). | |
| RowColumnScanning | ADC pin used, up to 3.3V and can be calibrated by using analogSet(float gain, float offset). In line 41, replace, pin 11 and pin 10 with pin 1 and pin 0 respectively. For “analogRead()”, use A4 and A5 instead of A0 and A1. After line 101, add delay(1); | ||
| 07. Strings | CharacterAnalysis | ||
| StringAdditionOperator | |||
| StringAppendOperator | |||
| StringCaseChanges | |||
| StringCharacters | |||
| StringComparisonOperators | ADC pin used, up to 3.3V and can be calibrated by using analogSet(float gain, float offset). | ||
| StringIndexOf | |||
| StringLength | |||
| StringLengthTrim | |||
| StringReplace | |||
| StringStartsWithEndsWith | |||
| StringSubstring | |||
| StringToInt |
Copyrights ©瑞晟微电子(苏州)有限公司 2021. All rights reserved. Terms of Use
